Thomas Williams, All American Renovations – Elite member of James Hardie™ ALLIANCE · Metro Atlanta and Middle Georgia
The holding power of a siding nail is in its head. Drive it a hair too deep and that head punches through the board, and now it’s holding nothing at all. The wall looks perfect. Nothing is fastened.
That one detail decides whether your siding lasts thirty years or starts flapping in eighteen months. And once the painter’s been through, you cannot see it.
If you’re getting Hardie siding, nails are the thing to watch, and this is the post to read while your wall is still open.
Why Does One Nail Matter This Much?
Because the board isn’t held by the shank of the nail. It’s held by the head pressing the board to the wall.
Overdrive it — sink it too deep — and the head goes through the face or out the back of the board. The nail is still there. It’s in the stud. It’s doing nothing. And the crew can’t see it either, because the painter comes behind them and putties over everything.
Then the seasons turn. That board expands and contracts like it’s designed to. The nails that never had grip start to work loose and pull. The board slips. It bows out. And one windy evening you hear your siding flapping against the wall.
By then your one-year warranty is up.
What Do Correctly Driven Hardie Siding Nails Look Like?
James Hardie documents this with pictures, and their instructions are specific:
- Use the nail line if your plank has one. If it doesn’t, the fastener goes between 3/4 inch and 1 inch from the top of the plank. We aim for one inch.
- Landed in a stud — every nail
- Joints landing on a stud — both boards
- Driven perpendicular to the siding and framing, not angled
- Head snug against the siding, no air space — not countersunk, not standing proud
Worth knowing: blind nailing is the preferred method. Face nailing is only for where code requires it in high-wind areas, and the instructions say it must not be mixed with blind nailing on the same job.
Get the placement too high and it kicks the bottom of the board out. Miss the stud and you’ve got nothing. Overdrive it and you’ve got nothing.
Honestly? That last one — a head snug with no air space, on every nail, all day — is one of the hardest things in this trade to do consistently. Which brings me to the part nobody talks about.
Why Is This The Hardest Thing To Get Right?
Air pressure. That’s it. That’s the whole fight.
A pneumatic nailer runs off an air compressor, and if a crew doesn’t turn that pressure down, the gun oversinks every nail. They can be hitting studs perfectly and still be destroying the wall, because the pressure blows those heads right through the board.
This has been my single biggest struggle with installers for eighteen years — since 2008, when I sat down and actually read Hardie’s best practices front to back and understood what you’re supposed to do and not do. I have worked with many, many crews in that time. Getting guys to turn the pressure down is the hardest habit to build in this entire trade.
So we stopped relying on habit and started using tools. I’m going to name them, because I’d rather every wall in Georgia get built right than keep this to myself.
For placement: the EZi-Gauge. Made by Wells Design Tool Company, available on Amazon. It’s an offset attachment that mounts on the end of the gun — you set it on top of the board, pull the trigger, and the nail lands at exactly one inch. Not too high, not too low. The model we run is the EZi-FC2, for fiber cement, on our Metabo HPT guns. Their site lists which attachment fits which gun.
For pressure: an inline preset regulator by THB. Even with the gauge we were still fighting air pressure, so a couple of years ago I sat down with my James Hardie tech rep and asked what we could do. He recommended one and gave us a few. It’s an inline preset pressure regulator for pneumatic air tools, preset so the compressor can’t deliver more than 116 PSI to the gun. Blue cylinder, says 116 right on it, hooks straight into the line. It physically will not let the gun blow through the board.
Here’s the part I want you to understand. With the pressure capped and the nail in a stud, that head is going to sit just slightly proud of the board. A little high.
And I’d rather see that than see it blown through. Hardie agrees with me in writing — their instructions say that if proper depth is hard to achieve with a pneumatic gun, you should choose a setting that under drives the nail. Not over.
But underdriven isn’t good enough either. The guy has to come back with a hammer and tap that board tight until the head sits snug with no air space behind it.
It takes more time. The end result is dramatically different.
Why Am I Telling You This?
Somebody’s going to read this and wonder why a contractor would publish the exact tools that solve his hardest problem. Fair question.
There is more work in this world than any one contractor could ever handle. I’m not short on houses. What the industry is short on is people who install this stuff correctly.
So if another contractor reads this, buys an EZi-Gauge and a THB regulator, and starts sending his crews out with the pressure capped — that’s a win. Not for me specifically. For every homeowner in Georgia who won’t have their siding flapping in four years.
I don’t need less competition. I need good, healthy competition. What I don’t need, and what none of us need, is more bad installers and more contractors who don’t care.
Go buy the tools.
What’s The Myth That Ruins Walls?
Somewhere along the way a lot of crews got it in their heads that if a house has OSB sheathing, you can nail fiber cement straight into the OSB and skip the studs.
That is half a truth, and the half they are missing is the half that matters.
James Hardie’s Best Practice Guide does allow siding to go directly to sheathing — over OSB at least 7/16 of an inch thick. But it is explicit about what that costs you: once you are fastening into sheathing without catching a stud, the siding has to be face nailed. Blind nailing is the method where the nails go through the sheathing and into the studs. That is the whole point of it.
So what is wrong is not going into OSB. It is going into OSB blind — fasteners hidden under the next course, nothing landing in a stud, and a wall that looks right on the day it is finished. That combination is not in the book anywhere, and it is what I find on nearly every wall that has come loose.
It feels solid when you do it. The board doesn’t move. And it will hold for a while — long enough for the crew to be paid and gone.
Which leads to the other thing I see, and it’s the cover-up. When boards are already loose, some crews will come back and pin back the siding across the whole wall so nothing moves and there are no immediate complaints.
Go read the documents on that one. Blind nailing is what they call for, with face nailing where high-wind code requires it — and James Hardie’s Best Practice Guide does address pin-backs, right there in the blind-nailing section. Pin-backed corners may be done for aesthetic purposes only. Finish nails are what it recommends, headed siding nails are allowed, and they go no closer than an inch from the end of a plank and three quarters of an inch from its edge.
But the sentence right after it is the one that matters: pin-backs are not a substitute for blind or face nailing. That is the whole distinction, and it is the one being dodged. A pin holding a corner flat for looks is in the manual. A field of pins across a wall, holding down boards that are loose because the nails never found a stud, is not — that is a cosmetic fastener doing structural work it was never meant to do, on a wall somebody had to rescue after the fact.
How Do We Actually Make Sure It Happens?
I’ll tell you exactly what we do, because talking about standards is easy and enforcing them isn’t.
We hold a first board, first nail session. Before a crew hangs anything on your house, we walk through our best practices together at the wall, on the first board, with the first nail.
We come back and check the job. Not at the end — during.
If there are issues, I make them rip it down. That’s the part that works. Eighteen years in, it’s the only thing I’ve found that makes it stick. If you want to work for me, you do it the way James Hardie says: on the nail line, in a stud, joints on studs, perpendicular, snug with no air space, not countersunk.
I use my Hardie tech reps and I’m glad to have them. But I don’t rely on somebody else to be the one who tells my crews they’re doing it wrong. That’s my job.
What Can You Watch For On Your Own Job?
You can’t inspect a finished wall. You can do this:
- While the wall is open, look at the nail heads. Are they sitting snug, or punched into the board?
- Ask what’s controlling the air pressure. If the answer is “the guys know,” that’s an answer.
- Ask where the studs are and how they’re finding them. Then ask what happens at the joints.
- Ask about the starter strip. If there isn’t one, that bottom board sits flat against the wall instead of kicked out where it belongs, and it throws off every row above it. That one is in the installation instructions, same as everything else on this page — it isn’t a preference of mine.
- After it’s done: press on a board. Does it move? Can you get a hand behind it? On a bad wall I can pull a board off without hardly trying.
If boards are flapping in the wind a year in, you already have your answer. It’s almost always the nails — placement too high, not in a stud, blown through, or all three at once.
What I’d Tell You If You Called Me
- Ask any contractor what PSI they run and how they control it. Nobody asks this. The answer tells you everything.
- Go look at the wall on day one, not day ten.
- “We nailed it to the OSB” is a red flag, not an explanation.
- A wall covered in pin-backs is a wall that wasn’t nailed right.
- Ask who checks the crew’s work, and when. If the answer is nobody, that’s your answer.
Job In Progress And Something Feels Off?
If you’re in Middle Georgia or Metro Atlanta and you’ve got siding going up right now that you’re uneasy about, call me. I’ll tell you what I’d look at. If it’s fine, I’ll tell you that too — and that’s a good phone call to get.
If your house is in Metro Atlanta, our Atlanta siding contractor page has real prices from our Metro Atlanta jobs.
Want the numbers on a whole job? Here’s what siding replacement costs in Middle Georgia. Still choosing a board? Not all fiber cement is the same, and the differences matter more than the brand name.
Sources: James Hardie installation instructions, technical documents and best practice guides. The air-pressure figure, the tools we use and our own inspection practice are All American Renovations’ own. Installation documents are revised periodically — work from the current revision for the product on your wall.

Thomas Williams is co-founder of All American Renovations, which he and his brother Pete started as a gutter business in 2001 and have run in Henry County, Georgia, for 25 years. He has installed James Hardie siding since 2007 and writes the company’s Learning Center. All American Renovations is an Elite member of James Hardie™ ALLIANCE, a CertainTeed ShingleMaster and an EPA Lead-Safe Certified Firm. Read Thomas’s full profile or connect with Thomas on LinkedIn.
